We are a leading Wholesaler of fosroc conplast wl waterproofing admixture, fosroc conbextra gp2, fosroc cebex 100 grout waterproofing chemical, fosroc lokfix e55s, fosroc brushbond grey waterproofing chemical and fosroc brushbond roofguard waterproofing chemical from Pune, India.
Conplast WL waterproofs by improving the quality of the concrete or mortar. It reduces the water demand for required workability and minimises segregation and bleeding. Thus it is more efficient compared to traditional powder waterproofers as its use results in two fold improvement of concrete or mortar.
Conbextra GP2 is supplied as a ready to use dry powder. The addition of a controlled amount of clean water produces a free flowing, non-shrink grout for gap thicknesses up to 100mm.
Conbextra GP2 is a blend of Portland cement, graded fillers and chemical additives which impart controlled expansion in the plastic state whilst minimising water demand. The low water demand ensures high early strength. The graded fillers are designed to assist uniform mixing and produce a consistent grout.
Cebex 100, a plasticised expanding grout admixture is supplied as a powder. The material is a combination of a plasticising agent and a gas producing expansion medium. The plasticing agent allows the use of a reduced water/cement ratio with consequent increased strengths and durability. The expansive medium counteracts the natural settlement and plastic shrinkage of the grout and aids stability and cohesion.
Lokfix E55 is a two component vinyl-ester anchoring material, supplied in single component cartridges with a static mixer nozzle. When applied it sets and cures rapidly to firmly secure a variety of steel fixings into concrete and masonry substrates.
Two grades of Lokfix E55 are available, selection is based upon substrate installation temperature and compliance:
Lokfix E55S: Standard temperature grade, optimised for substrate installation temperatures between -10 and +40 degree celcius.
Lokfix E55L: Low temperature grade, optimised for substrate installation temperatures: -20 to +15 degree celcius. Lokfix E55L does not have C1 seismic approval or fire testing.
Store between 35oC and 10oC in a shaded environment.
Powder + Liquid
Brushbond comprises a two component acrylic polymer modified cementitious coating supplied in ready to mix kits. Brushbond can be simply applied by stiff brush, roller, spray or trowel to obtain the desired texture.
Note : For potable water applications, please refer to Nitocote CM210 and Brushbond FLX lll datasheets
Brushbond Roof Guard is a single component acrylic polymer modified, fibre reinforced high build & easy roller applied / brushable coating available in different colours for application in multiple layers, minimum 3 layer application is recommended for best performance.
Brushbond TGP crystalline capillary waterproofing system contains proprietary blend of portland cement, quartz aggregate and special chemicals. In the presence of moisture, the active chemicals in Brushbond TGP crystalline waterproofing system penetrates concrete and react chemically with free lime to produce insoluble crystals. This crystalline growth reduces porosity by blocking capillaries and filling hairline non structural cracks (upto 0.25mm wide) caused by shrinkage or expansion. Unlike metallic and membrane types of waterproofing which only form a surface barrier, Brushbond TGP crytalline waterproofing system, in the presence of water, continues producing crystals and lasting imperviousness to water.
Dr. Fixit Primeseal is water-based primer composed of acrylic emulsion polymer, properly selected fine fillers, white pigments & additives in water as a medium. It is used as primer over exterior & interior building walls before application of water based paints.
Nitobond SBR is a modified styrene butadiene rubber emulsion which is supplied as a ready to use white liquid. It is designed to improve the qualities of site-batched cementitious mortars and slurries. Being resistant to hydrolysis, it is ideal for internal and external applications in conjunction with cement. Nitobond SBR has a VOC content 29g / litre.
Nitocote Wall Guard is water based polymer coating composed of high quality acrylic polymer, with weather resistant pigments, properly selected & graded fine fillers. It is used as a waterproofing & decorative coating for protection of exterior walls of the buildings from heavy wind driven rain.
Renderoc Plug is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a highly consistent, rapid setting mortar which is easy to apply in many difficult conditions. The material is based on a blend of cements, graded aggregates, special fillers and chemical additives which control the rate of set and minimise the risk of thermal cracking. Renderoc Plug provides an initial set time of approximately one minute.
Brushbond RFX is a two component acrylic polymer modified cementitious coating which consists of Brushbond RFX powder and Brushbond RFX liquid acrylic emulsion. It requires only the addition of clean water at site to produce an easily brushable coating. Brushbond RFX can simply be applied by stiff brush, roller or trowel to obtain the desired thickness.
Nitoflor Hardtop / Nitoflor Hardtop Standard are quality controlled, factory blended powder which are ready to use on site. They contain special hardwearing aggregates which have been selected for abrasion and wear resistant properties as well as shape and size.
Yes! I am Interested
Fosroc Brushcrete Waterproof Coating for Concrete & Masonry
Roofs, terraces, toilets, General Concrete repairs, etc
Brushcrete is a single component acrylic based polymer when blended with cement forms a composite polymer modified cementitious waterproofing system, When used in conjunction with fibre mesh forms a tough hard wearing surface.
Conplast P211 is a chloride free water reducing admixture based on selected sugar-reduced lignosulphonates. It is supplied as a brown solution which instantly disperses in water. Conplast P211 disperses the fine particles in the concrete mix, enabling the water content of the concrete to perform more effectively and improving the consistency of the concrete. This produces higher levels of workability for the same water content, allowing benefits such as water reduction and increased strengths to be taken.
Delivery Time: 5 days
Packaging Details: Conplast P211 is supplied in 5,20 and 200-liter containers.
Nitobond EP is based on solvent free epoxy resins containing pigments and fi ne fi llers. It is supplied as a two part material in preweighed quantities for ready onsite mixing and use. Coloured components - white base and green hardener - provide visual evidence that adequate mixing is achieved.
Yes! I am Interested
Dr fixit PU Sealants
Get Best Quote
Approx. Price: Rs 470 / PieceGet Latest Price
Cartridges of 600 ml
Surface Of Application
Country of Origin
Made in India
Dr. Fixit Silicone Sealant GPS Is a versatile one component sanitary acetic silicone sealant forsealing building joints and glazing systems. After application the silicone cures with atmosphericmoisture to form a durable rubber seal.
Renderoc RGL is supplied as a ready to use blend of dry powder, which requires only the site addition of clean water to produce a free-flowing, non-shrink microconcrete. The material is based on Portland cements, and fillers, and additives which impart controlled expansion characteristics in the plastic state, while minimising water demand. The low water requirement ensures high early strength and long-term durability.